Menu

Tech Tubes & Fittings

Tube Fittings, Pipe Fittings, Needle Valve, Ball Valve, Manifold Valves & more

Different types 2 Way Manifold for Pressure Transmitter

Different types of 2 Way Manifold Valves?

For the pressure transmitter, a 2-way valve manifold is used. One block valve and one drain or test valve make up a conventional 2-way valve manifold. Let's begin. 

Characteristics of the 2 way manifold valve

Techtube proposes to you the best manifold valves to create your work go smoothly and with a cycle without any leakage of fluids or gases. There are some of the characteristics of these 2 way manifold valves and they are: 

  • A wide range of materials is offered.
  • Low-torque operation with a high-pressure level There is up to 15000 ps available. 
  • Compact design heck Valve comes with Male/Female NPT (National Pipe Taper), BSPT (British Standard Pipe Taper), and BSPP (British Standard Parallel Pipe) end connectors, as well as dust caps.

 

Types of 2 way Manifold valves 

Direct Connect or inline 2 way Manifold valve 

Direct connect 2-way manifolds have female or male process connections and are also known as inline, block and bleed, and block and bleed 2-way manifolds. To connect this type of manifold to transmitters, a male National Pipe Taper(NPT) is used.
 

For these manifolds, only a 2-valve panel with a 12" NPT(National pipe taper) process connection is available. Female process connections are common on these manifolds, although male process connections are also accessible.
 

Coplanar 2 way Manifold Valve 

2-valve assembly coplanar manifolds with direct process connection on a coplanar manifold

On a coplanar manifold, a 2-valve system with a direct process connection

Coplanar manifolds have a process connection that comes in from the bottom, avoiding the requirement for a process flange. They're available with two valves and a two-valve gas metering setup. Process connection sizes of 12" and 14" are offered on coplanar manifolds.

 

Traditional 2 Way Manifold Valve

Traditional manifolds have a side connector. It's feasible to get them with two valves. Some traditional manifolds need a flange, whereas others do not. These manifolds come with 12" and 14" technique connectors.
 

Conventional 2 way Manifold Valve

Conventional Manifolds are a kind of 2 way manifold that has been around for an extended time. A traditional manifold has a 2-valve structure. If you need a totalizer manifold on the flank of a process flange rather than instantly on a pressure transmitter detector, you'll be required to utilize a normal manifold. Choice and traditional flanges are words used to characterize these flanges. There are two-valve conventional manifolds available. On the device side, there is a 2 18" center-to-center association.

 

Anyone who even has a remote idea about the fluid system and control would be familiar with the 2 way manifold for pressure transmitter. This device is used in the industrial process with the purpose of connecting a pressure transmitter with a process line. And while there are many different types of 2 way manifolds, they typically consist of two block valves and one equalizing valve. They are also maintenance and replacement friendly, as one can do the task without much effort.

 

There is no doubt that it is a valuable component, but given the importance of this instrument, you must ensure that you find a premium supplier of the same. It is not something where you can compromise the quality of the product. Luckily, Tech Tubes & Fittings is a trustworthy supplier of the same. You only need to state your requirement, and we will leave no stone left unturned in ensuring that you get a suitable response from our side.

For More Details on  Different types of 2 Way Manifold Valves contact us on sales1@techtubes.in

***Monel, Hastelloy, Inconel, Incoloy, SMO254, Nitronic, AL6XN, Stellite, Sanicro, Tantalum, Nimonic , Alloy A286, Invar, Cupronickel etc., are the trademarks of their respective companies.

Go Back

Comment